1 Preparation before installation: dual guarantee of safety and environment
1. Safety configuration of personnel and tools
Installation personnel must wear a complete set of insulated protective equipment, including insulated gloves, insulated shoes, and goggles that meet high-voltage operation standards, to avoid the risk of electric shock caused by direct contact with live parts. The tools should be selected from a professional set that is compatible with the insulation level, including insulation wrenches, multimeters, insulation testers, etc. The insulation performance of the tools should be verified before use to ensure that there is no damage or aging. At the same time, high-voltage warning signs should be set up in the work area, and a safety isolation zone of 1.5 meters or more should be designated to prohibit unrelated personnel from entering.
2. Compliance requirements for installation environment
The venue needs to meet the three core conditions of "dryness, ventilation, and light avoidance": the environmental humidity should be controlled between 20% -80% to prevent the electrolyte from getting damp and deteriorating; Reserve at least 0.8 meters of cabinet spacing and top ventilation space to ensure efficient operation of the cooling system; Keep away from open flames, heat sources, and corrosive gases, and maintain a temperature within the installation range of 0 ℃ -40 ℃. The ground must meet the standard of load-bearing capacity, with a minimum load-bearing capacity of 800kg per square meter, to prevent long-term deformation of the rack under pressure. In addition, the venue should be equipped with emergency equipment such as dry powder fire extinguishers (ABC type), and the distance from the fire escape should not exceed 5 meters.

2 Standardized installation process: full steps from assembly to debugging
1. Rack and module assembly
Operate in the order of "front frame and back module": First, fix the standard frame in the preset position, use a level to calibrate the verticality and flatness, and control the error within ± 2mm. Then, reinforce the frame with expansion bolts and the ground to ensure that there is no shaking of the frame. Subsequently, the battery modules are embedded into the rack layer by layer, with a spacing of 5cm between modules to reserve heat dissipation space. Each module is fastened with 4 sets of bolts, and the spring washers need to be flattened to prevent loosening. Finally, install the high-voltage BMS controller, which is usually fixed on the top of the rack for easy signal acquisition and operation.
2. Electrical connection and insulation testing
Firstly, remove the protective covers of the positive and negative terminals of the battery, and connect the module with copper bars or specialized high-voltage cables. Follow the wiring principle of "low voltage first, high voltage second, positive electrode first, negative electrode second". Apply conductive paste to the wiring to reduce contact resistance and seal it with insulation heat shrink tubing. The communication line connection needs to correspond to the port pins to ensure smooth signal communication between BMS and various modules. After the wiring is completed, use an insulation tester to test the insulation resistance of the system, which should not be less than 100M Ω. At the same time, verify the voltage value with a multimeter to confirm that there are no issues with reverse or false connections.
3. System debugging and trial operation
Start the BMS system for parameter initialization, set core parameters such as charge and discharge cut-off voltage and balance threshold, and match the requirements of actual application scenarios. Subsequently, perform no-load debugging to check the communication status and temperature display of each module to ensure there are no alarm messages. After normal no-load operation, enter a 24-hour trial run: first charge and discharge at 50% rated power for 3 cycles, monitor voltage balance and temperature changes; Switch to full power operation again to verify the system response speed and stability. During the trial operation, the temperature difference should be controlled within 5 ℃.

3 Daily operation and maintenance strategy: preventive maintenance and status monitoring
1. The core content of periodic inspection
Establish a three-level inspection system of "daily inspection+weekly inspection+quarterly inspection": daily inspection checks real-time data such as voltage, current, temperature through BMS backend, focusing on whether the voltage difference of the battery cell exceeds 50mV and whether the temperature exceeds the safe range; Conduct on-site visual inspection during weekly inspection, including checking for deformation of the casing, loose wiring terminals, normal operation of the cooling fan, and cleaning of dust accumulation on the surface of the cabinet; The quarterly inspection adopts professional equipment for testing, monitoring the health status of the battery cells through an internal resistance tester, and retesting the insulation resistance with an insulation tester to ensure that the parameters meet the standards.
2. Fine management of charging and discharging and environment
Optimize charging and discharging strategies to extend lifespan: avoid long-term full charge and discharge, recommend daily charging to 80% -90% and discharging to 20% -30% to reduce deep cycle losses; When the ambient temperature is below 5 ℃, activate the low-temperature preheating function before charging to prevent lithium dendrite precipitation from puncturing the diaphragm. Regularly inspect the cooling system, clean the air duct filter every month, and replace the coolant (liquid cooling system) every six months to ensure heat dissipation efficiency. At the same time, keep the environment clean and dry, and add dehumidification equipment during the rainy season to avoid short circuits caused by moisture.
4 Common troubleshooting: precise positioning and efficient handling
1. Diagnosis and solution of typical faults
• Rapid capacity decay: Retrieve historical data through BMS to check for frequent overcharging, overdischarging, or long-term high-temperature operation. If it is caused by poor cell consistency, activate the active balancing function for adjustment; If a single battery cell experiences severe attenuation, it is necessary to hot plug and replace the faulty module.
• Voltage imbalance alarm: First check if the wiring is loose, then check the individual voltage distribution through BMS, and separately balance and charge the modules with excessive voltage difference. If the balance is ineffective, check the BMS balance circuit and replace the balance board if necessary.
• Abnormal temperature rise: Immediately stop the machine to check the cooling system, clean the fan or replace the faulty water pump. If it is local battery overheating, check for internal short circuits, isolate the faulty module and replace it.
• Communication interruption: Check if the communication cable is damaged and if the interface is loose. If there is still no signal after restarting the BMS controller, check the compatibility of the communication protocol or replace the communication board of the faulty module.
2. Emergency response and safety plan
In case of emergency, follow the "power-off isolation handling" process: when a thermal runaway warning (temperature surge of 10 ℃/min or more) is detected, immediately trigger the high-voltage power-off, activate the fire extinguishing device, and evacuate personnel to a safe area; If electrolyte leakage occurs, wear protective clothing to clean up the leaked material, absorb it with sand and treat it as hazardous waste, and do not rinse with water. Regularly organize emergency drills, and conduct at least two disposal drills for scenarios such as thermal runaway and short circuits every year to ensure that personnel are proficient in the operating procedures.





