How To Store Lithium Batteries To Prevent Physical Damage?

Feb 01, 2025 Leave a message

Content Menu

● Introduction

● Storage Container Selection

● Storage Environment Setup

● Battery Placement and Handling

● Protection from External Factors

● How to check the condition of lithium batteries before storage?

● Visual Inspection

● Check of Electrical Parameters

● Functional Testing

● Consideration of Storage History

● FAQ

>> 1. How do I properly store a lithium battery when not in use?

>> 2. What causes a lithium battery to swell?

>> 3. Are lithium batteries safe for air travel?

>> 4. How does the charging rate affect a lithium battery?

>> 5. Can I use a non original charger for my lithium battery?

Introduction:

To prevent physical damage to lithium batteries during storage, several measures can be taken. Firstly, store them in a dedicated, shockproof and anti collision storage box or container to avoid accidental bumps and drops. It's also advisable to keep them in a stable and dry place, away from areas with high traffic or where they might be knocked over. Secondly, do not stack heavy objects on top of the batteries to prevent them from being crushed. If storing multiple batteries, make sure to separate them properly to avoid contact that could cause scratching or deformation. Thirdly, when transporting or handling the stored batteries, use appropriate tools and handle them with care, following the correct operating procedures to minimize the risk of physical damage.

u16053863552177453809fm253fmtautoapp138fJPEG

Storage Container Selection

Opt for Non-Conductive Containers: Use storage containers made of non-conductive materials like plastic or hard rubber. These materials prevent electrical conduction and subsequent short circuits that could damage the battery. For example, plastic storage bins with dividers are ideal for keeping multiple batteries separated.

Use Specialized Battery Holders: For small lithium batteries such as those in cameras or remote controls, specialized battery holders can be used. These holders are designed to hold the batteries securely in place, preventing them from moving around and potentially getting damaged.

Storage Environment Setup

Choose a Stable and Flat Storage Location: Place the batteries on a stable and flat surface to avoid accidental tipping or falling. A dedicated storage cabinet or a shelf in a cool, dry room is a good choice. Avoid storing them on the floor where they might be stepped on or kicked.

Keep Away from Vibrations and Shock: Store the batteries in an area free from vibrations and shocks. Machinery rooms, near vibrating equipment, or areas prone to frequent movement should be avoided. Excessive vibrations can cause internal components of the battery to shift or become loose, leading to physical damage.

Battery Placement and Handling

Store Batteries Upright: When storing lithium batteries, keep them in an upright position. This helps maintain the stability of the internal structure and prevents the electrolyte from flowing unevenly, which could cause damage over time.

Separate Batteries Properly: If storing multiple batteries, separate them to prevent contact and friction. Use dividers in the storage container or place each battery in an individual compartment. This is especially important for larger batteries like those in power tools or electric vehicles to avoid scratches and dents.

Handle with Care During Storage: When placing or retrieving batteries from storage, handle them gently. Avoid dropping, throwing, or applying excessive force. Even a small impact can cause internal damage to the battery.

Protection from External Factors

Keep Away from Sharp Objects: Ensure that the storage area is free from sharp objects that could puncture or scratch the battery casing. A punctured casing can lead to electrolyte leakage and other serious problems.

Protect from Temperature Extremes: Avoid storing batteries in extremely hot or cold environments. High temperatures can cause the battery to expand and potentially rupture, while low temperatures can affect the battery's chemical composition and make it more brittle, increasing the risk of physical damage.

u23673362631985148021fm253fmtautoapp138fJPEG

How to check the condition of lithium batteries before storage?

Before storing lithium batteries, it's essential to check their condition through the following methods:

Visual Inspection

Examine the Casing: Check the battery casing carefully for any signs of damage, such as cracks, bulges, dents or scratches. Cracks and bulges may indicate internal problems and potential leakage risks. Even small scratches can be a concern as they might provide an entry point for moisture.

Inspect the Terminals: Examine the battery terminals for signs of corrosion, discoloration or physical damage. Corroded terminals can affect the battery's performance and may lead to poor electrical contact. Discoloration might suggest overheating or other issues.

Check of Electrical Parameters

Measure the Voltage: Use a multimeter to measure the open-circuit voltage of the battery. Compare the measured voltage with the rated voltage of the battery. If the voltage is significantly lower than the rated value, it could indicate that the battery is deeply discharged or has internal problems. For example, a fully charged 18650 lithium battery typically has a voltage around 4.2V. If it measures much lower, further investigation is needed.

Check the Internal Resistance: Some advanced multimeters or specialized battery testers can measure the internal resistance of the battery. An abnormally high internal resistance may suggest that the battery's performance has degraded or there are internal faults. As the battery ages or is damaged, the internal resistance usually increases.

Functional Testing

Charge and Discharge Test: If possible, perform a simple charge and discharge test. Charge the battery to its full capacity and then discharge it at a moderate rate. Observe the charging and discharging process. If the battery charges or discharges too quickly or too slowly, or if it stops charging or discharging prematurely, it may have a problem. For example, if a battery that should take 2 hours to charge is fully charged in 30 minutes, it's likely something is wrong.

Compatibility Test: Try using the battery in the device it's intended for. If the device shows abnormal behavior, such as not turning on, turning off unexpectedly or having a significantly shorter battery life than usual, the battery may be faulty. However, make sure to rule out other possible causes in the device itself before concluding that the battery is at fault.

Consideration of Storage History

Review Usage and Storage Conditions: Think about the battery's previous usage and storage conditions. If it has been stored in extreme temperatures, high humidity or has been subject to physical shocks, it may be more likely to have problems. For example, a battery that was left in a hot car for an extended period may have degraded performance.

u4264848077319381856fm253fmtautoapp138fJPEG

FAQ

1.Q: How do I properly store a lithium battery when not in use?
A: It is best to store a lithium battery at a 40% - 60% charge level. High or low charge levels can accelerate the battery's degradation during long term storage. Store the battery in a cool, dry place away from direct sunlight and extreme temperatures. If possible, keep it in a fire resistant container in case of any unforeseen issues.

2.Q: What causes a lithium battery to swell?
A: Swelling in a lithium battery is usually caused by internal gas generation. This can occur due to overcharging, over discharging, or exposure to high temperatures. Overcharging can cause the electrolyte to break down and produce gas. Similarly, when the battery is over discharged, the chemical reactions can become imbalanced, leading to gas formation. High - temperature conditions can also accelerate these unwanted chemical reactions that result in gas production and subsequent swelling.

3.Q: Are lithium batteries safe for air travel?
A: Lithium ion and lithium polymer batteries are generally allowed on air travel, but there are strict regulations. For carry on luggage, small consumer grade lithium ion batteries (such as those in smartphones, laptops) are usually permitted. However, the total lithium content of spare batteries is restricted. For checked luggage, the rules are more stringent, and in some cases, large lithium ion batteries, especially those in high capacity devices like some power tools, may not be allowed at all. This is to minimize the risk of fire or explosion during flight.

4.Q: How does the charging rate affect a lithium battery?
A: A high charging rate, such as fast charging, can save time but may also generate more heat. Excessive heat can accelerate the degradation of the battery over time. Although modern batteries and chargers are designed to manage heat during fast charging, frequent use of very high speed charging may slightly reduce the battery's long term lifespan compared to slower, more gentle charging methods. However, the impact is often relatively small if the charging system has proper heat management.

5.Q: Can I use a non original charger for my lithium battery?
A: It is not recommended to use a non original charger. Non original chargers may not have the correct voltage and current output specifications for your battery. Using an incompatible charger can lead to overcharging, under charging, or unstable charging, which can damage the battery, reduce its lifespan, and even pose safety risks such as overheating or fire. It's best to use the charger provided by the device manufacturer or a charger that is specifically approved for your lithium battery device.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry