Balancing Performance And Safety: A Comprehensive Analysis Of The Charge Discharge Thermal Characteristics Of 48V Lithium Ion Battery Pack

Oct 28, 2024 Leave a message

 
Research Background

Addressing carbon emissions issues, EV and HEV are receiving attention
Li ion batteries are suitable for MHEVs and their prices have decreased
Temperature is important for the lifespan and energy of Li ion batteries

 
Experimental Purpose

Study on the thermal behavior of 48VLi ion battery pack
Using 25 thermocouples for monitoring

 
Battery Parameters

Adopting prismatic NCM battery
The battery pack is composed of 36 connected batteries

 
Experimental Layout

Using 25 thermocouples to monitor battery temperature
The test bench includes four parts: battery pack, etc

 
Charge-discharge Cycle

Conduct two complete charge discharge cycle tests
Avoid high temperature and thermal failure of battery packs

 
Theoretical Background

Introduce the relevant theories of battery thermal generation

 
Result Analysis

SOC and voltage test results
Thermal performance: temperature distribution of different modules
Analysis of average temperature, maximum and minimum temperature, etc

 
Discussion Summary

Battery research: phenomena such as positive and negative electrode temperatures
Module research: Module 1 is more sensitive to current
Research on battery pack: Temperature is affected by current

 
Future Work

Develop efficient cooling systems and management strategies

 

 

This article uses 25 thermocouples to experimentally study the temperature distribution and behavior of a 48V lithium-ion (Li ion) battery pack during two charge discharge cycles. The results indicate that better convective heat transfer occurs on the outer surface of the packaging, while the middle battery reaches its maximum temperature. Differences were also observed in the behavior of the three modules. The discharge cycle shows a temperature increase of 5.8 ° C, and the temperature gradient of the battery pack increases from 1.3 ° C to 2.7 ° C. This study emphasizes the importance of evaluating the thermal behavior of each module and the complexity of lithium-ion battery pack systems. In the same study, discoveries about batteries, modules, and battery packs can provide valuable insights for designing efficient cooling systems for lithium-ion battery packs.

 

 

1. Introduction

 

Lithium ion batteries: Rechargeable lithium-ion batteries are considered suitable energy storage devices for mild hybrid vehicles due to their high energy density, specific power, lightweight, low self discharge rate, high recyclability, and long lifespan. In the past 13 years, the price of lithium-ion battery packs has significantly decreased. However, high temperature and uneven temperature distribution are the main problems of lithium-ion batteries, and temperature plays an important role in their lifecycle and energy capacity.

 

Shortcomings of previous research: Previous studies on the thermal behavior of lithium-ion batteries in mild hybrid vehicles mainly focused on individual batteries or battery packs, lacking detailed analysis of the impact of external parameters (such as the presence of other batteries) on battery thermal behavior. In addition, the research scope on the thermal behavior of 48V lithium-ion battery packs is limited, and there is a lack of experimental studies on the detailed temperature distribution of the entire battery pack.

 

The purpose of this study:  is to experimentally investigate the thermal behavior of a 48V lithium-ion battery pack through two complete charge discharge cycles. Using 25 thermocouples to measure at different locations within the battery pack, we hope to provide valuable insights into the heat generation of the battery pack and help select the appropriate battery cooling system.

 

 

 

2. Experimental Determination

 

Lithium ion battery parameters: Lithium ion batteries are typically composed of an anode, cathode, electrolyte, and current collector. Cylindrical, prismatic, and pouch shaped batteries are used in the automotive industry, and prismatic designs can improve space utilization and flexibility. This study used a prismatic NCM lithium-ion battery with a nominal capacity of 8.23Ah. The battery pack consists of 36 batteries connected in a 12s3p configuration, which has the advantages of easy installation, modularity, safety and compactness, minimal impact on vehicle weight, and high cost-effectiveness.

 

6401

 

 

Experimental layout: The experimental testing device includes a battery pack, a high voltage high current AVL battery simulator controlled by the AVL PUMA system, a K-type temperature sensor with two data acquisition modules (ES620 ETAS), and a computer unit for monitoring and storing data. Use 25 thermocouples to monitor the temperature of the battery, with measurement points located in the three modules of the battery pack. Thermocouples help detect temperature changes between the positive and negative terminals of the same battery.

 

 

641

 

 

Charge and discharge cycles: Two complete charge and discharge cycle tests were conducted with initial temperatures and states of charge (SoC) of 26 ° C and 47%, respectively. The maximum and minimum currents were 237A and -237A, respectively. The SoC reached twice the highest and lowest values, i.e. 91% and 10%, and the test ended when the SoC reached the initial value. To avoid thermal failure of the battery pack at high temperatures, the test was terminated when the temperature reached 40 ° C. In this study, the temperature limit was reached at the end of the second cycle.

 

 

642

 

 

Theoretical background: The temperature effect of batteries is related to internal materials and chemical reactions. The thermal generation of lithium-ion batteries at normal temperatures is related to charge transfer and chemical reactions during charging and discharging processes. Thermal generation includes reversible processes (entropy heat) and irreversible processes. According to the laws of thermodynamics, the transient behavior of heat generated inside a battery can lead to different temperature changes. To study the thermal behavior of lithium-ion batteries and battery packs, a naming convention and related parameters for temperature were defined, such as maximum temperature, minimum temperature, temperature difference, and average temperature.

 

 

6431

6432

6433

6434

 

 

 

 

3. Results

 

 

SOC and Voltage

 


Figure below shows the voltage, current, and SoC of the battery pack. The testing time is divided into 8 parts of two cycles, with LD, EC, LC, and ED representing late discharge, early charge, late charge, and early discharge, respectively. In the first part LD1, the current is -237A, and the battery pack and battery voltage decrease; In the EC1 section, the current is 237A, the SoC reaches 33%, and the battery pack voltage increases; In the LC1 section, the current drops to 33A and the battery pack voltage increases; In the ED1 section, the current is -237A, and the SoC and voltage decrease. In the second cycle, the current, SoC, and voltage of the battery pack showed a similar time evolution as the first cycle, and the test ended at 2105s.

 

6441

 

 

Lithium ion battery packs typically require long periods of high constant current in practical applications, so BMS will reduce output to ensure safety. Figure above shows a sudden decrease in current limit during the late charging phase due to battery thermal management.

 

 

Thermal performance

 


Figure a shows the temperature time history of 8 thermocouples in Module 1. The values of T1 and+12 were in the middle of the module temperature range at the beginning of the test, but dropped to the lowest at the end of the test. T1 and -01 were equal to Tmin at the beginning of the first cycle, and the temperature of the battery in the middle of the module was the highest.

 


Figure b shows the temperature distribution of module 2, where T2, -12 is Tmin, T2,+01 is the second lowest temperature, and T2,+04 is Tmax.

 


Figure c shows the temperature distribution of module 3, where T3, -01 is Tmin, T3,+12 is the second lowest temperature, T3,+04, T3, -06, and T3, -07 is Tmax.

 

 

6451

 

 

Figure below shows the time history of the average temperature, maximum temperature, minimum temperature, and temperature difference of the battery pack and each module. The Trise of the battery pack in EC1 and EC2 is 1.6 ° C and 1.2 ° C, respectively. During the full discharge cycle (combination of ED1 and LD2), the Trise is approximately 5.8 ° C. The maximum ∆ T is 2.0 ° C and 3.2 ° C at the end of EC1 and EC2, respectively, while the minimum ∆ T is 1.3 ° C and 2.2 ° C at the end of the first and second full charging cycles, respectively T can be divided into the difference between Tmax and Tavg, as well as the difference between Tavg and Tmin. The difference between Tavg and Tmin varies linearly when the current changes significantly, while the difference between Tmax and Tavg is sensitive to current and nonlinear.

 

 

6461

 

 

 

 

4. Discussion

 


Battery research: In the same lithium-ion battery, the temperature of the positive terminal is higher than that of the negative terminal, with a maximum temperature difference of about 0.6 ° C. This phenomenon has also been mentioned in literature. In addition, at the end of the two cycles, Tmin appears in T1,+12 and T1, -01 in module 1, T2, -12 and T2,+01 in module 2, and T3, -01 and T3,+12 in module 3. This indicates that Tmin appears on the external battery of the battery pack, due to better convective heat transfer and cooling effect on the module boundary surface compared to the ambient temperature. And the Tmax of each module appears in the middle battery, but this is not symmetrical, indicating the dynamic behavior and temperature non-uniformity of each battery. This phenomenon illustrates the complexity of this dynamic system and emphasizes the importance of evaluating the temperature behavior of all modules in the battery pack.

 


Module research: The Tavg of Module 1 is higher than that of the battery pack in the first half of LDs, ECs, EDs, and LCs, indicating that Module 1 is more sensitive to high currents than other modules, generates more heat, rises faster in temperature, and exchanges heat better than other modules. This indicates the complexity of the battery pack system, and the thermal behavior of each module should be studied and inspected separately.

 


Battery pack research: In lithium-ion batteries, modules, and battery packs, temperature always increases in EDs, LDs, and ECs. Therefore, Tmax appears not only in the middle of LC1 and LC2, but also at the end of EC1 and EC2. In other words, when there is high current, the temperature will rise because more lithium ions should move through the membrane and generate more heat. Therefore, at the beginning of LCs, there will be a temperature drop, followed by the observation of quasi steady state behavior of temperature. 

 

During the complete discharge cycle between two charging cycles, the temperature monotonically increases; Overall, Trise increased by 5.8 ° C from its initial value of 31.8 ° C. In addition, ∆ T also showed the same upward trend from 1.3 ° C to 2.7 ° C. This is due to the high current based on equation (2) during this period, as well as the sensitivity of module 1 to current. In addition, the Trise patterns in the two charging cycles showed similar trends. At the beginning, it rises, then falls, and finally maintains a quasi steady state temperature. Therefore, when a higher current is applied to the battery pack, higher Trise and ∆ T will be achieved.

 


∆ T can be divided into the difference between Tmax and Tavg, as well as the difference between Tavg and Tmin. Tmax is highly sensitive to temperature gradients and varies over time, while Tmin is less sensitive to changes in current. Therefore, the most important part of the temperature change in the battery pack is due to the behavior of Tmax. In other words, the difference between Tavg and Tmin varies linearly when there is a significant difference in current, and the slope changes. The difference between Tmax and Tavg is very sensitive to current, and the slope will increase over time. Therefore, in the second scenario, except for significant variations in large current differences, ∆ T exhibits no linear behavior in both constant and dynamic currents. Future work should focus on developing efficient cooling systems and exploring different thermal management strategies to improve the performance and safety of lithium-ion battery packs based on the results obtained from this study.

 

 

5. Summary

 

This article studies the thermal behavior of 48V lithium-ion battery packs under dynamic current, which is crucial for understanding the safe and reliable operation of lithium-ion battery packs, especially in applications that require high power and energy density.

 

The experimental results indicate that the temperature behavior of the battery pack is complex and nonlinear, with differences among different batteries, modules, and the entire battery pack. The temperature outside the battery pack is lower than the internal battery due to better convective heat transfer, and the positive terminal temperature of a single battery is higher than the negative terminal temperature. A module is more sensitive to high currents, resulting in faster temperature rise and heat generation, which can only be obtained by studying all modules in the same lithium-ion battery pack.

 

The temperature behavior of the battery pack is mainly influenced by Tmax, which is more sensitive to current. Trise is mainly due to high current and the heat generated by the movement of lithium ions through the separator. The difference between Tmin and Tavg varies linearly under constant current, while the difference between Tmax and Tavg varies nonlinearly under current changes, especially under large current differences.

 

Overall, the research findings indicate the importance of individually examining and evaluating the thermal behavior of each battery, module, and the entire battery pack to understand the complexity and nonlinear behavior of lithium-ion battery packs under dynamic currents. The results of this study will contribute to the development of more efficient and reliable battery thermal management systems for lithium-ion battery packs in automotive applications in the future. When determining battery thermal management strategies and parameters, it is necessary to consider the differences between module Tavg, Tavg's dependence on Tmax, and the impact of battery location on its temperature changes.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry